The 64 Audio U12t is 12.6Ω at 108.0 dB/mW; the Shure SE846 is 9Ω at 114.0 dB/mW. This page is only about what they ask of an amplifier — not how they sound, which no specification on either sheet can tell you.
The 64 Audio U12t needs 6.0 dB more than the Shure SE846 to reach the same loudness — 0.16 mW against 0.04 mW.
| Specification | 64 Audio U12t | Shure SE846 |
|---|---|---|
| Impedance | 12.6 Ω | 9 Ω |
| Sensitivity | 108.0 dB/mW | 114.0 dB/mW |
| Sensitivity (voltage) | 127.0 dB/V | 134.5 dB/V |
| Power for 100 dB | 0.16 mW | 0.04 mW |
| Voltage for 100 dB | 45 mV | 19 mV |
| Current for 100 dB | 3.5 mA | 2.1 mA |
| Highest source impedance that leaves them alone (one-eighth rule) | 1.57 Ω | 1.12 Ω |
| Sources that reach 100 dB out of 280 | 280 | 280 |
Every source in the database that drives one of them drives the other. On power, the choice between these two changes nothing about what amplifier you need.
6 sources are low enough in output impedance for the 64 Audio U12t under the one-eighth rule but not for the Shure SE846 (FiiO K11, FiiO BTR7, FiiO M11S, 3 more).
33 sources stay below the audible-hiss threshold with the 64 Audio U12t but cross it with the Shure SE846 (Kiwi Ears Allegro Mini, FiiO KA13, JDS Labs Atom+ (2nd gen), 30 more).
280 of the 280 sources here reach 100 dB on both. That count is about power only — the output-impedance and hiss lines above are separate questions, and a source can pass this one and fail those.
The gap between these two in decibels does not change with volume — it is a property of the two headphones. What changes is the size of the numbers, and it changes fast: every 10 dB costs ten times the power. The row that matters is the one nearest the level you listen at, and for most people that is nearer the top of this table than the bottom.
The 64 Audio U12t is more demanding than 8% of the 567 non-electrostatic models in this database; the Shure SE846 than 1%. Both figures use the same measure as the rest of the site: whichever runs out first against a 2 V, 100 mW dongle, voltage or power.
| dB SPL | 64 Audio U12t power | 64 Audio U12t voltage | Shure SE846 power | Shure SE846 voltage |
|---|---|---|---|---|
| 80 | 1.6 µW | 4 mV | 0.4 µW | 2 mV |
| 85 | 5.0 µW | 8 mV | 1.3 µW | 3 mV |
| 90 | 0.02 mW | 14 mV | 4.0 µW | 6 mV |
| 95 | 0.05 mW | 25 mV | 0.01 mW | 11 mV |
| 100 | 0.16 mW | 45 mV | 0.04 mW | 19 mV |
| 105 | 0.50 mW | 79 mV | 0.13 mW | 34 mV |
105 dB is included because forum power figures are usually quoted there or higher. It is also a level that damages hearing in minutes — how many minutes is its own calculator.
| Source | Price | Headroom, 64 Audio U12t | Headroom, Shure SE846 | Output impedance | Noise |
|---|---|---|---|---|---|
| JadeAudio JA11 | $20 | 18.7 dB | 23.3 dB | 0.5 Ω | 1.7 µV |
| FiiO KA11 | $29 | 30.9 dB | 35.4 dB | 0.7 Ω | 1.7 µV |
| FiiO BTR13 | $59 | 27.8 dB | 32.3 dB | 0.6 Ω | 1.0 µV |
Of the 280 sources here, 280 reach 100 dB on both. That is the easy axis. 23 of them also publish an output impedance low enough for both under the one-eighth rule and a noise figure that stays below the audible-hiss threshold with both — the rest either fail one of those or never printed the number at all, and 208 of them are in the second group.
The cheapest of the 23 is the JadeAudio JA11, at $20. It leaves 18.7 dB of headroom on the 64 Audio U12t and 23.3 dB on the Shure SE846, its output impedance is 0.5 Ω against a one-eighth limit of 1.57 Ω and 1.12 Ω, and its noise figure puts the hiss floor 8 dB and 1 dB below the 20 dB SPL this site treats as the point where a quiet room stops hiding it.
Cheapest that satisfies three published numbers is not the same as best, and none of it is about how either headphone sounds. To put either model against a source this page does not mention, or to change the target loudness, use the amplifier matcher.
| Model | As printed | Tolerance | Standard |
|---|---|---|---|
| 64 Audio U12t | 10 Hz – 20 kHz | not printed | not printed |
| Shure SE846 | 15 Hz–20 kHz | not printed | not printed |
64 Audio prints 10 Hz – 20 kHz for the U12t. Shure prints 15 Hz–20 kHz for the SE846.
Neither range has a tolerance printed beside it, and that is the whole of what this section can tell you. A wider range on one sheet is not deeper bass or more treble on that headphone: without a tolerance, neither number says how loud either model is at the ends of its own range, so the difference between the two is a difference between two pieces of marketing copy. A ±dB figure is what turns a range into a specification, and of the 490 models whose maker prints a range, 58 print it.
None of this is a measurement. What each maker publishes, and what it is worth, is set out in the frequency response audit.
Each model has a page of its own with the full source list, the hiss estimate and the provenance of every figure above: 64 Audio U12t and Shure SE846. Every figure on this page comes from what 64 Audio and Shure published, or is derived from it — what 64 Audio publishes and what Shure publishes, both counted.