The Abyss AB-1266 Phi TC is 50Ω at 88.0 dB/mW; the Abyss Diana MR is 30Ω at 93.0 dB/mW. This page is only about what they ask of an amplifier — not how they sound, which no specification on either sheet can tell you.
The AB-1266 Phi TC needs 5.0 dB more than the Diana MR to reach the same loudness — 16 mW against 5.0 mW.
| Specification | AB-1266 Phi TC | Diana MR |
|---|---|---|
| Impedance | 50 Ω | 30 Ω |
| Sensitivity | 88.0 dB/mW | 93.0 dB/mW |
| Sensitivity (voltage) | 101.0 dB/V | 108.2 dB/V |
| Power for 100 dB | 16 mW | 5.0 mW |
| Voltage for 100 dB | 0.89 V | 0.39 V |
| Current for 100 dB | 17.8 mA | 12.9 mA |
| Highest source impedance that leaves them alone (one-eighth rule) | 6.25 Ω | 3.75 Ω |
| Sources that reach 100 dB out of 280 | 275 | 280 |
5 of the 280 sources have the power for the Diana MR but not for the AB-1266 Phi TC — Apple USB-C dongle (EU), Zoom AMS-22, Steinberg UR22C, 2 more.
1 source is low enough in output impedance for the AB-1266 Phi TC under the one-eighth rule but not for the Diana MR (Shanling H5).
275 of the 280 sources here reach 100 dB on both. That count is about power only — the output-impedance and hiss lines above are separate questions, and a source can pass this one and fail those.
The gap between these two in decibels does not change with volume — it is a property of the two headphones. What changes is the size of the numbers, and it changes fast: every 10 dB costs ten times the power. The row that matters is the one nearest the level you listen at, and for most people that is nearer the top of this table than the bottom.
The AB-1266 Phi TC is more demanding than 97% of the 567 non-electrostatic models in this database; the Diana MR than 81%. Both figures use the same measure as the rest of the site: whichever runs out first against a 2 V, 100 mW dongle, voltage or power.
| dB SPL | AB-1266 Phi TC power | AB-1266 Phi TC voltage | Diana MR power | Diana MR voltage |
|---|---|---|---|---|
| 80 | 0.16 mW | 89 mV | 0.05 mW | 39 mV |
| 85 | 0.50 mW | 0.16 V | 0.16 mW | 69 mV |
| 90 | 1.6 mW | 0.28 V | 0.50 mW | 0.12 V |
| 95 | 5.0 mW | 0.50 V | 1.6 mW | 0.22 V |
| 100 | 16 mW | 0.89 V | 5.0 mW | 0.39 V |
| 105 | 50 mW | 1.58 V | 16 mW | 0.69 V |
105 dB is included because forum power figures are usually quoted there or higher. It is also a level that damages hearing in minutes — how many minutes is its own calculator.
| Source | Price | Headroom, AB-1266 Phi TC | Headroom, Diana MR | Output impedance | Noise |
|---|---|---|---|---|---|
| JadeAudio JA11 | $20 | 0.8 dB | 7.5 dB | 0.5 Ω | 1.7 µV |
| FiiO KA11 | $29 | 9.1 dB | 16.1 dB | 0.7 Ω | 1.7 µV |
| FiiO BTR11 | $36 | 0.8 dB | 7.9 dB | 0.5 Ω | 8.0 µV |
Of the 280 sources here, 275 reach 100 dB on both. That is the easy axis. 70 of them also publish an output impedance low enough for both under the one-eighth rule and a noise figure that stays below the audible-hiss threshold with both — the rest either fail one of those or never printed the number at all, and 203 of them are in the second group.
The cheapest of the 70 is the JadeAudio JA11, at $20. It leaves 0.8 dB of headroom on the AB-1266 Phi TC and 7.5 dB on the Diana MR, its output impedance is 0.5 Ω against a one-eighth limit of 6.25 Ω and 3.75 Ω, and its noise figure puts the hiss floor 34 dB and 27 dB below the 20 dB SPL this site treats as the point where a quiet room stops hiding it.
Cheapest that satisfies three published numbers is not the same as best, and none of it is about how either headphone sounds. To put either model against a source this page does not mention, or to change the target loudness, use the amplifier matcher.
| Model | As printed | Tolerance | Standard |
|---|---|---|---|
| AB-1266 Phi TC | 5 Hz - 45 KHz | not printed | not printed |
| Diana MR | 42Hz – 45 KHz, -3 dB @ 5 Hz | not printed | not printed |
Abyss prints 5 Hz - 45 KHz for the AB-1266 Phi TC and 42Hz – 45 KHz, -3 dB @ 5 Hz for the Diana MR.
Diana MR: The decibel figure in this row is not a tolerance on the range: it is attached to a single frequency, 5 Hz, which sits far below the 42 Hz the range starts at. The page separately claims "-3dB @ 10 Hz" in its marketing text. The three numbers cannot all describe the same thing, so none of them is recorded here as a tolerance.
Neither range has a tolerance printed beside it, and that is the whole of what this section can tell you. A wider range on one sheet is not deeper bass or more treble on that headphone: without a tolerance, neither number says how loud either model is at the ends of its own range, so the difference between the two is a difference between two pieces of marketing copy. A ±dB figure is what turns a range into a specification, and of the 490 models whose maker prints a range, 58 print it.
None of this is a measurement. What each maker publishes, and what it is worth, is set out in the frequency response audit.
Each model has a page of its own with the full source list, the hiss estimate and the provenance of every figure above: Abyss AB-1266 Phi TC and Abyss Diana MR. Every figure on this page comes from what Abyss published, or is derived from it — what that maker publishes, counted.