The Sennheiser HD 569 is 23Ω at 98.6 dB/mW; the Sennheiser HD 820 is 300Ω at 97.8 dB/mW. This page is only about what they ask of an amplifier — not how they sound, which no specification on either sheet can tell you.
The HD 820 needs 0.8 dB more than the HD 569 to reach the same loudness — 1.7 mW against 1.4 mW.
| Specification | HD 569 | HD 820 |
|---|---|---|
| Impedance | 23 Ω | 300 Ω |
| Sensitivity | 98.6 dB/mW | 97.8 dB/mW |
| Sensitivity (voltage) | 115.0 dB/V | 103.0 dB/V |
| Power for 100 dB | 1.4 mW | 1.7 mW |
| Voltage for 100 dB | 0.18 V | 0.71 V |
| Current for 100 dB | 7.7 mA | 2.4 mA |
| Highest source impedance that leaves them alone (one-eighth rule) | 2.88 Ω | 37.50 Ω |
| Sources that reach 100 dB out of 280 | 280 | 280 |
Every source in the database that drives one of them drives the other. On power, the choice between these two changes nothing about what amplifier you need.
20 sources are low enough in output impedance for the HD 820 under the one-eighth rule but not for the HD 569 (Zoom AMS-22, Arturia MiniFuse 2, Arturia MiniFuse 1, 17 more).
1 source stays below the audible-hiss threshold with the HD 820 but crosses it with the HD 569 (Schiit Mjolnir 3).
280 of the 280 sources here reach 100 dB on both. That count is about power only — the output-impedance and hiss lines above are separate questions, and a source can pass this one and fail those.
The gap between these two in decibels does not change with volume — it is a property of the two headphones. What changes is the size of the numbers, and it changes fast: every 10 dB costs ten times the power. The row that matters is the one nearest the level you listen at, and for most people that is nearer the top of this table than the bottom.
The HD 820 is more demanding than 93% of the 567 non-electrostatic models in this database; the HD 569 than 53%. Both figures use the same measure as the rest of the site: whichever runs out first against a 2 V, 100 mW dongle, voltage or power.
| dB SPL | HD 569 power | HD 569 voltage | HD 820 power | HD 820 voltage |
|---|---|---|---|---|
| 80 | 0.01 mW | 18 mV | 0.02 mW | 71 mV |
| 85 | 0.04 mW | 32 mV | 0.05 mW | 0.13 V |
| 90 | 0.14 mW | 56 mV | 0.17 mW | 0.22 V |
| 95 | 0.44 mW | 0.10 V | 0.52 mW | 0.40 V |
| 100 | 1.4 mW | 0.18 V | 1.7 mW | 0.71 V |
| 105 | 4.4 mW | 0.32 V | 5.2 mW | 1.25 V |
105 dB is included because forum power figures are usually quoted there or higher. It is also a level that damages hearing in minutes — how many minutes is its own calculator.
| Source | Price | Headroom, HD 569 | Headroom, HD 820 | Output impedance | Noise |
|---|---|---|---|---|---|
| JadeAudio JA11 | $20 | 11.9 dB | 2.9 dB | 0.5 Ω | 1.7 µV |
| FiiO KA11 | $29 | 21.9 dB | 11.2 dB | 0.7 Ω | 1.7 µV |
| FiiO BTR11 | $36 | 14.1 dB | 2.6 dB | 0.5 Ω | 8.0 µV |
Of the 280 sources here, 280 reach 100 dB on both. That is the easy axis. 69 of them also publish an output impedance low enough for both under the one-eighth rule and a noise figure that stays below the audible-hiss threshold with both — the rest either fail one of those or never printed the number at all, and 208 of them are in the second group.
The cheapest of the 69 is the JadeAudio JA11, at $20. It leaves 11.9 dB of headroom on the HD 569 and 2.9 dB on the HD 820, its output impedance is 0.5 Ω against a one-eighth limit of 2.88 Ω and 37.50 Ω, and its noise figure puts the hiss floor 20 dB and 32 dB below the 20 dB SPL this site treats as the point where a quiet room stops hiding it.
Cheapest that satisfies three published numbers is not the same as best, and none of it is about how either headphone sounds. To put either model against a source this page does not mention, or to change the target loudness, use the amplifier matcher.
| Model | As printed | Tolerance | Standard |
|---|---|---|---|
| HD 569 | 10 to 28,000 Hz | not printed | not printed |
| HD 820 | 6 Hz - 48,000 Hz (-10 dB) | -10 dB | not printed |
Sennheiser prints 10 to 28,000 Hz for the HD 569 and 6 Hz - 48,000 Hz (-10 dB) for the HD 820.
Only one of the two is a specification. The range printed for the HD 820 comes with a tolerance; the one printed for the HD 569 does not, and a range without a ±dB figure says nothing about how loud that model is at either end of it. The two cannot be compared number against number, however similar they look in the table. Of the 490 models whose maker prints a range, 58 print the tolerance.
None of this is a measurement. What each maker publishes, and what it is worth, is set out in the frequency response audit.
Each model has a page of its own with the full source list, the hiss estimate and the provenance of every figure above: Sennheiser HD 569 and Sennheiser HD 820. Every figure on this page comes from what Sennheiser published, or is derived from it — what that maker publishes, counted.