The Hidizs MK12 x DucBloke is 32Ω at 111.0 dB (no reference unit printed); the Hidizs MP143 Salt is 17Ω at 103.0 dB (no reference unit printed). This page is only about what they ask of an amplifier — not how they sound, which no specification on either sheet can tell you.
The MP143 Salt needs 8.0 dB more than the MK12 x DucBloke to reach the same loudness — 0.50 mW against 0.08 mW.
| Specification | MK12 x DucBloke | MP143 Salt |
|---|---|---|
| Impedance | 32 Ω | 17 Ω |
| Sensitivity | 111.0 dB | 103.0 dB |
| Sensitivity (voltage) | 125.9 dB/V | 120.7 dB/V |
| Power for 100 dB | 0.08 mW | 0.50 mW |
| Voltage for 100 dB | 50 mV | 92 mV |
| Current for 100 dB | 1.6 mA | 5.4 mA |
| Highest source impedance that leaves them alone (one-eighth rule) | 4.00 Ω | 2.12 Ω |
| Sources that reach 100 dB out of 280 | 280 | 280 |
One caution before reading the rows. Hidizs MK12 x DucBloke and Hidizs MP143 Salt printed a decibel figure with no reference unit, so this page reads it as per milliwatt. If it is really per volt, each of them needs far more than the table says. Why the two readings differ by so much.
Every source in the database that drives one of them drives the other. On power, the choice between these two changes nothing about what amplifier you need.
14 sources stay below the audible-hiss threshold with the MP143 Salt but cross it with the MK12 x DucBloke (FiiO BTR11, FiiO K11 R2R, Lake People G103-S Mk II, 11 more).
280 of the 280 sources here reach 100 dB on both. That count is about power only — the output-impedance and hiss lines above are separate questions, and a source can pass this one and fail those.
The gap between these two in decibels does not change with volume — it is a property of the two headphones. What changes is the size of the numbers, and it changes fast: every 10 dB costs ten times the power. The row that matters is the one nearest the level you listen at, and for most people that is nearer the top of this table than the bottom.
The MP143 Salt is more demanding than 30% of the 567 non-electrostatic models in this database; the MK12 x DucBloke than 12%. Both figures use the same measure as the rest of the site: whichever runs out first against a 2 V, 100 mW dongle, voltage or power.
| dB SPL | MK12 x DucBloke power | MK12 x DucBloke voltage | MP143 Salt power | MP143 Salt voltage |
|---|---|---|---|---|
| 80 | 0.8 µW | 5 mV | 5.0 µW | 9 mV |
| 85 | 2.5 µW | 9 mV | 0.02 mW | 16 mV |
| 90 | 7.9 µW | 16 mV | 0.05 mW | 29 mV |
| 95 | 0.03 mW | 28 mV | 0.16 mW | 52 mV |
| 100 | 0.08 mW | 50 mV | 0.50 mW | 92 mV |
| 105 | 0.25 mW | 90 mV | 1.6 mW | 0.16 V |
105 dB is included because forum power figures are usually quoted there or higher. It is also a level that damages hearing in minutes — how many minutes is its own calculator.
| Source | Price | Headroom, MK12 x DucBloke | Headroom, MP143 Salt | Output impedance | Noise |
|---|---|---|---|---|---|
| JadeAudio JA11 | $20 | 25.8 dB | 15.0 dB | 0.5 Ω | 1.7 µV |
| FiiO KA11 | $29 | 34.0 dB | 26.8 dB | 0.7 Ω | 1.7 µV |
| FiiO BTR13 | $59 | 31.0 dB | 23.7 dB | 0.6 Ω | 1.0 µV |
Of the 280 sources here, 280 reach 100 dB on both. That is the easy axis. 57 of them also publish an output impedance low enough for both under the one-eighth rule and a noise figure that stays below the audible-hiss threshold with both — the rest either fail one of those or never printed the number at all, and 208 of them are in the second group.
The cheapest of the 57 is the JadeAudio JA11, at $20. It leaves 25.8 dB of headroom on the MK12 x DucBloke and 15.0 dB on the MP143 Salt, its output impedance is 0.5 Ω against a one-eighth limit of 4.00 Ω and 2.12 Ω, and its noise figure puts the hiss floor 9 dB and 15 dB below the 20 dB SPL this site treats as the point where a quiet room stops hiding it.
Cheapest that satisfies three published numbers is not the same as best, and none of it is about how either headphone sounds. To put either model against a source this page does not mention, or to change the target loudness, use the amplifier matcher.
| Model | As printed | Tolerance | Standard |
|---|---|---|---|
| MK12 x DucBloke | 10Hz-45kHz | not printed | not printed |
| MP143 Salt | 20Hz to 40kHz | not printed | not printed |
Hidizs prints 10Hz-45kHz for the MK12 x DucBloke and 20Hz to 40kHz for the MP143 Salt.
For both: Hidizs prints this figure in the body copy of the product page. The only specification table on that page belongs to a different product — one of the company’s DAC dongles — and there is no frequency row in a table for this model.
Neither range has a tolerance printed beside it, and that is the whole of what this section can tell you. A wider range on one sheet is not deeper bass or more treble on that headphone: without a tolerance, neither number says how loud either model is at the ends of its own range, so the difference between the two is a difference between two pieces of marketing copy. A ±dB figure is what turns a range into a specification, and of the 490 models whose maker prints a range, 58 print it.
None of this is a measurement. What each maker publishes, and what it is worth, is set out in the frequency response audit.
Each model has a page of its own with the full source list, the hiss estimate and the provenance of every figure above: Hidizs MK12 x DucBloke and Hidizs MP143 Salt. Each figure on this page is labelled on those pages with where it came from, including the ones Hidizs never published — what that maker publishes, counted.