The Moondrop PARA is 8Ω at 80.0 dB/mW; the Moondrop PARA 2 is 9Ω at 85.5 dB/mW. This page is only about what they ask of an amplifier — not how they sound, which no specification on either sheet can tell you.
The PARA needs 5.5 dB more than the PARA 2 to reach the same loudness — 100 mW against 28 mW.
| Specification | PARA | PARA 2 |
|---|---|---|
| Impedance | 8 Ω | 9 Ω |
| Sensitivity | 80.0 dB/mW | 85.5 dB/mW |
| Sensitivity (voltage) | 101.0 dB/V | 106.0 dB/V |
| Power for 100 dB | 100 mW | 28 mW |
| Voltage for 100 dB | 0.89 V | 0.50 V |
| Current for 100 dB | 111.8 mA | 56.0 mA |
| Highest source impedance that leaves them alone (one-eighth rule) | 1.00 Ω | 1.12 Ω |
| Sources that reach 100 dB out of 280 | 130 | 223 |
93 of the 280 sources have the power for the PARA 2 but not for the PARA — FiiO SnowSky Tiny B, Tanchjim Stargate II, ddHiFi TC35Air, 90 more.
1 source is low enough in output impedance for the PARA 2 under the one-eighth rule but not for the PARA (Astell&Kern SR35).
130 of the 280 sources here reach 100 dB on both. That count is about power only — the output-impedance and hiss lines above are separate questions, and a source can pass this one and fail those.
The gap between these two in decibels does not change with volume — it is a property of the two headphones. What changes is the size of the numbers, and it changes fast: every 10 dB costs ten times the power. The row that matters is the one nearest the level you listen at, and for most people that is nearer the top of this table than the bottom.
The PARA is more demanding than 100% of the 567 non-electrostatic models in this database; the PARA 2 than 89%. Both figures use the same measure as the rest of the site: whichever runs out first against a 2 V, 100 mW dongle, voltage or power.
| dB SPL | PARA power | PARA voltage | PARA 2 power | PARA 2 voltage |
|---|---|---|---|---|
| 80 | 1.0 mW | 89 mV | 0.28 mW | 50 mV |
| 85 | 3.2 mW | 0.16 V | 0.89 mW | 90 mV |
| 90 | 10 mW | 0.28 V | 2.8 mW | 0.16 V |
| 95 | 32 mW | 0.50 V | 8.9 mW | 0.28 V |
| 100 | 100 mW | 0.89 V | 28 mW | 0.50 V |
| 105 | 316 mW | 1.59 V | 89 mW | 0.90 V |
105 dB is included because forum power figures are usually quoted there or higher. It is also a level that damages hearing in minutes — how many minutes is its own calculator.
| Source | Price | Headroom, PARA | Headroom, PARA 2 | Output impedance | Noise |
|---|---|---|---|---|---|
| FiiO KA11 | $29 | 0.9 dB | 6.9 dB | 0.7 Ω | 1.7 µV |
| JDS Labs Atom+ (2nd gen) | $99 | 4.0 dB | 10.0 dB | 0.7 Ω | 1.99 µV |
| FiiO KA15 | $109 | 1.6 dB | 7.6 dB | 0.8 Ω | 1.7 µV |
Of the 280 sources here, 130 reach 100 dB on both. That is the easy axis. 53 of them also publish an output impedance low enough for both under the one-eighth rule and a noise figure that stays below the audible-hiss threshold with both — the rest either fail one of those or never printed the number at all, and 71 of them are in the second group.
The cheapest of the 53 is the FiiO KA11, at $29. It leaves 0.9 dB of headroom on the PARA and 6.9 dB on the PARA 2, its output impedance is 0.7 Ω against a one-eighth limit of 1.00 Ω and 1.12 Ω, and its noise figure puts the hiss floor 34 dB and 29 dB below the 20 dB SPL this site treats as the point where a quiet room stops hiding it.
Cheapest that satisfies three published numbers is not the same as best, and none of it is about how either headphone sounds. To put either model against a source this page does not mention, or to change the target loudness, use the amplifier matcher.
| Model | As printed | Tolerance | Standard |
|---|---|---|---|
| PARA | 15-53kHz (IEC61094, Free Field) | not printed | IEC61094 (free field) |
| 20-20kHz (IEC60318-4, -3dB) | -3 dB | IEC60318-4 | |
| PARA 2 | 20Hz-42kHz (IEC61094, Free Field) | not printed | IEC61094 (free field) |
| 20Hz-20kz (IEC60318-4, -3dB) | -3 dB | IEC60318-4 |
Moondrop prints two ranges, “15-53kHz (IEC61094, Free Field)” and “20-20kHz (IEC60318-4, -3dB)”, for the PARA and two ranges, “20Hz-42kHz (IEC61094, Free Field)” and “20Hz-20kz (IEC60318-4, -3dB)”, for the PARA 2.
PARA 2: Moondrop prints the narrow range as “20Hz-20kz”, without the H. It is quoted here exactly as it stands on the page.
Both sheets print a tolerance, which is rare enough to be worth pointing at: only 58 of the 490 models with a printed range do. These two ranges can be set against each other, because each of them says how far down the response is allowed to be at the ends.
None of this is a measurement. What each maker publishes, and what it is worth, is set out in the frequency response audit.
Each model has a page of its own with the full source list, the hiss estimate and the provenance of every figure above: Moondrop PARA and Moondrop PARA 2. Every figure on this page comes from what Moondrop published, or is derived from it — what that maker publishes, counted.