ART HeadAmp 4 Pro: power output and what it will drive

The ART HeadAmp 4 Pro is a desktop amplifier at $130. It delivers 98 mW into 32Ω and 33 mW into 300Ω, which ranks it 218 of 280 for raw power among the sources in this database.

Measured at 100 dB SPL it has comfortable headroom on 516 of the 567 dynamic and planar headphones catalogued here, enough but not generous on 40, only marginal on 5 and not enough power for 6. Power is published at 30Ω, 100Ω; the rest of the table is derived from those figures. Output noise is not published, so the hiss estimate cannot be run.

The manufacturer publishes 100 mW into 30Ω, 100 mW into 100Ω. Everything else in the table above is worked out from those figures, and this table says which is which.

Derivation holds output voltage steady between and beyond the published loads rather than output power, because that is what an amplifier actually does. The full method is written up here.

Source: artproaudio.com.

Ordered from easiest to hardest to drive. Headroom is measured at 100 dB SPL, which is louder than almost anyone listens — a small negative number means the source still plays loud, just without reserve for peaks.

These figures come from each manufacturer's own sensitivity rating. A handful of planars — the HiFiMAN Susvara and the Abyss AB-1266 in particular — are widely reported to need far more than their published sensitivity implies, so treat a bare pass on those as optimistic rather than settled.

The manufacturer does not publish an output noise figure for this source, so the hiss estimate that runs on every other page here cannot be run on this one. Rather than substitute a plausible number, this page leaves the question open.

If you know the noise figure from a measurement you trust, the hiss calculator takes it directly and tells you where that noise lands in your own in-ears.

At 47Ω output impedance, the one-eighth rule says this source suits headphones of 376.0Ω and above. 561 of the 567 models here fall below that. That is most of the database, not a niche — 222 of them multi-driver in-ears, and the mismatch tilts the frequency response audibly rather than subtly.

The rule is a rule of thumb, not physics: a source impedance below one eighth of the headphone's keeps the interaction under about 1 dB. The checker works it out for any pair.

Of the 280 sources here, 12 do everything the ART HeadAmp 4 Pro does as a headphone output: reach 100 dB on every headphone it reaches and stay inside the one-eighth rule wherever it does. The cheapest of them is the FiiO KA11 at $29, against this one’s $130 — $101 less, and a USB dongle rather than a desktop amplifier.

The cheaper one also publishes a noise figure, which the ART HeadAmp 4 Pro does not — so on the paperwork it is ahead, not merely level.

This counts a headphone output and nothing else. Inputs, converters, microphone preamps, balanced outputs, the volume control, the case and the warranty are all outside it, and any of them can be the reason to buy the dearer box. What the count does say is that the three numbers a maker can be held to do not separate them.

Worked out in advance against its closest rivals: vs JDS Labs Atom Amp 2 · vs JDS Labs Atom+ (2nd gen) · vs Schiit Magni Heresy · vs Schiit Magni Piety · vs Schiit Magni Unity · vs Schiit Magni+ · vs Schiit Vali 2+ · vs Schiit Vali 3 · vs SMSL HO100 · vs Topping L30 II. Each of those pages lists the headphones that tell the two apart.

Or put any two side by side in the source comparison tool, or run your own headphones through the amplifier matcher. Or see every ART source in the database, and how much of what this site says about them came from ART’s own documents.