Hype 10 vs Hype 4: which needs more amplifier?

The Thieaudio Hype 10 is 18Ω at 87.6 dB/mW; the Thieaudio Hype 4 is 17Ω at 105.0 dB (no reference unit printed). This page is only about what they ask of an amplifier — not how they sound, which no specification on either sheet can tell you.

The Hype 10 needs 17.4 dB more than the Hype 4 to reach the same loudness — 17 mW against 0.32 mW.

The numbers that decide it

SpecificationHype 10Hype 4
Impedance18 Ω17 Ω
Sensitivity87.6 dB/mW105.0 dB
Sensitivity (voltage)105.0 dB/V122.7 dB/V
Power for 100 dB17 mW0.32 mW
Voltage for 100 dB0.56 V73 mV
Current for 100 dB31.1 mA4.3 mA
Highest source impedance
that leaves them alone (one-eighth rule)
2.25 Ω2.12 Ω
Sources that reach 100 dB
out of 280
264280

One caution before reading the rows. Thieaudio Hype 4 printed a decibel figure with no reference unit, so this page reads it as per milliwatt. If it is really per volt, that model needs far more than the table says. Why the two readings differ by so much.

Where the two part company

16 of the 280 sources have the power for the Hype 4 but not for the Hype 10 — Apple USB-C dongle (US), Apple USB-C dongle (EU), JadeAudio JA11, 13 more.

3 sources stay below the audible-hiss threshold with the Hype 10 but cross it with the Hype 4 (FiiO BTR11, Rupert Neve RNHP, Schiit Mjolnir 3).

264 of the 280 sources here reach 100 dB on both. That count is about power only — the output-impedance and hiss lines above are separate questions, and a source can pass this one and fail those.

What each one needs from 80 to 105 dB

The gap between these two in decibels does not change with volume — it is a property of the two headphones. What changes is the size of the numbers, and it changes fast: every 10 dB costs ten times the power. The row that matters is the one nearest the level you listen at, and for most people that is nearer the top of this table than the bottom.

The Hype 10 is more demanding than 88% of the 567 non-electrostatic models in this database; the Hype 4 than 23%. Both figures use the same measure as the rest of the site: whichever runs out first against a 2 V, 100 mW dongle, voltage or power.

dB SPLHype 10 powerHype 10 voltageHype 4 powerHype 4 voltage
800.17 mW56 mV3.2 µW7 mV
850.55 mW99 mV0.01 mW13 mV
901.7 mW0.18 V0.03 mW23 mV
955.5 mW0.31 V0.10 mW41 mV
10017 mW0.56 V0.32 mW73 mV
10555 mW0.99 V1.0 mW0.13 V

105 dB is included because forum power figures are usually quoted there or higher. It is also a level that damages hearing in minutes — how many minutes is its own calculator.

The cheapest source that satisfies both

SourcePriceHeadroom, Hype 10Headroom, Hype 4Output impedanceNoise
FiiO KA11$2911.3 dB28.8 dB0.7 Ω1.7 µV
FiiO BTR13$598.2 dB25.7 dB0.6 Ω1.0 µV
iBasso DC03 Pro$695.0 dB22.2 dB0.12 Ω0.9 µV

Of the 280 sources here, 264 reach 100 dB on both. That is the easy axis. 66 of them also publish an output impedance low enough for both under the one-eighth rule and a noise figure that stays below the audible-hiss threshold with both — the rest either fail one of those or never printed the number at all, and 193 of them are in the second group.

The cheapest of the 66 is the FiiO KA11, at $29. It leaves 11.3 dB of headroom on the Hype 10 and 28.8 dB on the Hype 4, its output impedance is 0.7 Ω against a one-eighth limit of 2.25 Ω and 2.12 Ω, and its noise figure puts the hiss floor 30 dB and 13 dB below the 20 dB SPL this site treats as the point where a quiet room stops hiding it.

Cheapest that satisfies three published numbers is not the same as best, and none of it is about how either headphone sounds. To put either model against a source this page does not mention, or to change the target loudness, use the amplifier matcher.

Both pages in full

Each model has a page of its own with the full source list, the hiss estimate and the provenance of every figure above: Thieaudio Hype 10 and Thieaudio Hype 4. Each figure on this page is labelled on those pages with where it came from, including the ones Thieaudio never published — what that maker publishes, counted.

↑