Thieaudio Hype 10: how much amplifier do you need?

The Thieaudio Hype 10 is 18Ω with a sensitivity of 87.6 dB/mW, which is 105.0 dB/V. To reach 100 dB SPL — genuinely loud, louder than most people listen — it needs 17 mW, or 0.56 V across the drivers.

That is a moderate load. Most USB dongles handle it without complaint; the weakest phone outputs will run out of volume before they run out of quality. 251 of 280 sources here have enough headroom. The cheapest portable source that does the job is the FiiO SnowSky Tiny A at $22.

Sensitivity here is in dB per milliwatt. Manufacturers often quote dB per volt instead and leave the unit off, which is the single most common reason online calculators give answers that are 10–15 dB wrong. The converter explains the difference.

Thieaudio, as the shop reproduces it, publishes this as 105 dB/Vrms — a figure per volt, not per milliwatt. At 18Ω the two differ by 17.4 dB, so the 87.6 dB/mW above is that published number converted, not a different measurement.

This is the conversion that online calculators skip. Quote the per-volt number as if it were per-milliwatt and this headphone looks 17 dB easier to drive than it is — which is roughly the difference between a dongle being enough and not being enough.

One caveat about the source. Almost everything in this database comes from a document the maker published. This entry does not: the figures above stand on someone else's product page — Hangout.Audio, a retailer — and not on any page Thieaudio publishes. Shops usually copy the factory table faithfully and this one may well be exact — but a shop can also carry an old revision, and if Thieaudio changes the number there is nothing here that would notice. It is the weakest provenance on this site, which is why it is written on the page rather than left in a footnote.

Thieaudio does have a site, and it is where these figures ought to be. The product pages carry a “Technical Details” tab that renders empty, and three of the four models in this database — Hype 2, Hype 10 and Phantom — return 404 from the catalogue altogether. The maker has a page and publishes nothing on it.

Source: hangout.audio. How this data was built.

Most people listen between 75 and 85 dB. The 100 dB row is the one worth planning around: it gives you headroom for dynamic peaks without designing your system for a volume that would damage your hearing in under fifteen minutes. The safe listening calculator puts numbers on that.

Every source in the database, judged at 100 dB SPL into 18Ω. “Headroom” is how much power is left over above what the headphone needs — 10 dB means ten times the required power, which is what you want for dynamic peaks.

Hiss. At 105.0 dB/V these are sensitive enough to reveal a source's own noise floor. The noisiest source in the database, the Schiit Mjolnir 3, would put its hiss at roughly 13 dB SPL in these headphones — clearly audible in quiet passages. The hiss calculator lets you check your own amplifier's noise figure.

Output impedance. At 18Ω these want a source output impedance below 2.25Ω to satisfy the one-eighth rule. Of the 192 sources that publish one, 35 miss it, the worst being the Bottlehead Crack (OTL kit) at 120.0Ω; the other 88 publish no output impedance at all, so they cannot be checked either way. Above that threshold the source starts shaping the frequency response. Check yours here.

Worked out in advance against its own stable: vs Hype 2 · vs Hype 4 · vs Hype 4 MKII · vs Monarch MK3 · vs Monarch MKII · vs Monarch MKIV · vs Oracle MKII · vs Origin · vs Prestige LTD. Each of those pages counts the sources that drive one and not the other.

Or open the comparison tool to put any two models side by side, or browse all 578. Or see every Thieaudio headphone in the database, and how much of what this site says about them came from Thieaudio’s own documents.