Moondrop Variations: how much amplifier do you need?

The Moondrop Variations is 15.2Ω with a sensitivity of 99.8 dB/mW, which is 118.0 dB/V. To reach 100 dB SPL — genuinely loud, louder than most people listen — it needs 1.0 mW, or 0.13 V across the drivers.

That puts it in the easy category. A phone, a laptop headphone jack or the cheapest USB dongle will drive it to painful levels. Of the 280 sources in the database, 274 have at least 10 dB of headroom and another 6 have enough. The cheapest portable source that does the job is the Apple USB-C dongle (US) at $9.

Sensitivity here is in dB per milliwatt. Manufacturers often quote dB per volt instead and leave the unit off, which is the single most common reason online calculators give answers that are 10–15 dB wrong. The converter explains the difference.

Moondrop publishes this as 118 dB/Vrms (@1kHz) — a figure per volt, not per milliwatt. At 15.2Ω the two differ by 18.2 dB, so the 99.8 dB/mW above is that published number converted, not a different measurement.

This is the conversion that online calculators skip. Quote the per-volt number as if it were per-milliwatt and this headphone looks 18 dB easier to drive than it is — which is roughly the difference between a dongle being enough and not being enough.

Moondrop prints the impedance as 15.2Ω±15% (@1kHz), not as a bare number. Everything on this page is calculated with the nominal 15.2Ω, and the rest of that line is quoted here rather than tidied away, because how a figure is qualified is part of the specification too.

Source: moondroplab.com. How this data was built.

Most people listen between 75 and 85 dB. The 100 dB row is the one worth planning around: it gives you headroom for dynamic peaks without designing your system for a volume that would damage your hearing in under fifteen minutes. The safe listening calculator puts numbers on that.

Every source in the database, judged at 100 dB SPL into 15.2Ω. “Headroom” is how much power is left over above what the headphone needs — 10 dB means ten times the required power, which is what you want for dynamic peaks.

Hiss. At 118.0 dB/V these are sensitive enough to reveal a source's own noise floor. The noisiest source in the database, the Schiit Mjolnir 3, would put its hiss at roughly 26 dB SPL in these headphones — clearly audible in quiet passages. The hiss calculator lets you check your own amplifier's noise figure.

Output impedance. At 15.2Ω these want a source output impedance below 1.90Ω to satisfy the one-eighth rule. Of the 192 sources that publish one, 39 miss it, the worst being the Bottlehead Crack (OTL kit) at 120.0Ω; the other 88 publish no output impedance at all, so they cannot be checked either way. Above that threshold the source starts shaping the frequency response. Check yours here.

Worked out in advance against its own stable: vs Andromeda 2020 · vs Armature Art 12 · vs Armature Art 24 · vs Chu II · vs ER4XR · vs Hexa · vs IE 200 · vs IE 600 · vs Meteor · vs Monarch MK3 · vs Psyche · vs Quarks · vs S12 Pro · vs S8 · vs SE215 · vs SE846 · vs Starfield II · vs U12t · vs Zero:RED. Each of those pages counts the sources that drive one and not the other.

Or open the comparison tool to put any two models side by side, or browse all 578. Or see every Moondrop headphone in the database, and how much of what this site says about them came from Moondrop’s own documents.