Beyerdynamic DT 990 Edition (600Ω): how much amplifier do you need?

The Beyerdynamic DT 990 Edition (600Ω) is 600Ω. Its maker prints a sensitivity of 96.0 dB and never says whether that is per milliwatt or per volt, so this page reads it as per milliwatt — on that reading it needs 2.5 mW to reach 100 dB SPL, or 1.23 V across the drivers. If the figure is really per volt, it needs far more.

That is a moderate load. Most USB dongles handle it without complaint; the weakest phone outputs will run out of volume before they run out of quality. 243 of 280 sources here have enough headroom. The cheapest portable source that does the job is the FiiO KA11 at $29.

This maker printed a decibel figure and no reference unit, so the number above is shown exactly as printed. Everything below reads it as per milliwatt, which is the commoner convention on a sheet that omits the unit — if it is really per volt, this headphone is about 2 dB harder to drive than the rest of this page assumes. The converter explains the difference.

Beyerdynamic publishes a sensitivity of 96 dB and does not state whether that is per milliwatt or per volt — the spec sheet simply stops at the number.

Both readings are given here so you can judge for yourself. If that 96 dB is per milliwatt, the figures on this page are right as they stand. If it is per volt, the real sensitivity is 93.8 dB/mW — 2 dB lower at 600Ω — and everything above understates what these need by that much. The per-milliwatt reading is the one shown, because it is the more common convention on a spec sheet that omits the unit; treat it as an indication rather than a specification.

Source: north-america.beyerdynamic.com, api.beyerdynamic.de. How this data was built.

Most people listen between 75 and 85 dB. The 100 dB row is the one worth planning around: it gives you headroom for dynamic peaks without designing your system for a volume that would damage your hearing in under fifteen minutes. The safe listening calculator puts numbers on that.

Every source in the database, judged at 100 dB SPL into 600Ω. “Headroom” is how much power is left over above what the headphone needs — 10 dB means ten times the required power, which is what you want for dynamic peaks.

Hiss. At 98.2 dB/V these are sensitive enough to reveal a source's own noise floor. The noisiest source in the database, the Schiit Mjolnir 3, would put its hiss at roughly 6 dB SPL in these headphones — faintly audible in a silent room. The hiss calculator lets you check your own amplifier's noise figure.

Output impedance. At 600Ω these want a source output impedance below 75.00Ω to satisfy the one-eighth rule. Of the 192 sources that publish one, 1 misses it, the worst being the Bottlehead Crack (OTL kit) at 120.0Ω; the other 88 publish no output impedance at all, so they cannot be checked either way. Above that threshold the source starts shaping the frequency response. Check yours here.

Worked out in advance against its own stable: vs Amiron Home · vs Custom One Pro Plus · vs Custom Studio · vs DJ 300 PRO X · vs DT 1350 · vs DT 1770 PRO MKII · vs DT 1990 PRO MK II · vs DT 240 Pro · vs DT 270 PRO · vs DT 275 PRO · vs DT 700 Pro X · vs DT 770 Pro (32Ω) · vs DT 770 Pro (80Ω) · vs DT 770 PRO Black Edition (80Ω) · vs DT 770 Pro X Limited · vs DT 880 Edition (32Ω) · vs DT 900 Pro X · vs DT 990 Edition (250Ω) · vs DT 990 Edition (32Ω) · vs DT 990 Pro (80Ω) · vs MMX 300 (32Ω) · vs MMX 300 PRO · vs MMX 330 PRO · vs T1 2nd Gen (600Ω) · vs T1 3rd Gen (32Ω) · vs T5 (3rd Generation) · vs T5p 2nd Gen · vs TYGR 300 R. Each of those pages counts the sources that drive one and not the other.

Or open the comparison tool to put any two models side by side, or browse all 578. Or see every Beyerdynamic headphone in the database, and how much of what this site says about them came from Beyerdynamic’s own documents.